24V DC Brushless Motor 0.9s 3m Folding Car Park Barriers Price
Applications: Parking management system, parking lot, Highway toll station,
hotel, park, residential, school, personal house.
DZ-138 barrier gate specifications:
| DZ-138 barrier gate | V06T | V09T |
| Max Boom Length and Diameter | 2500mm, Ф75mm | 3000mm, Ф75mm |
| Open/Close Time | 0.6sec | 0.9sec,2.5sec,4.5sec |
| Power Supply | 24/100/240VAC,50/60Hz | 24/100/240VAC,50/60Hz |
| Power Consumption | max.150W | 100w |
| Machine Case | Varnished 2.0mm steel plate | Varnished 2.0mm steel plate |
| Machine Case Size(W*D*H) | 342*312*959mm | 342*312*959mm |
| Net Weight | 43kg | 42.6kg |
| Operating Temperature Range℃ | -45℃~+85℃ | -45℃~+85℃ |
| Driving Method | Servo motor | Servo motor |
| Protection System(IP) | 65 | 65 |
| Insulation Class | F | F |
| Relative Humidity | ≤90% | ≤90% |
| Motor Speed | 3000r/min | 3000r/min |
| Remote Control Distance | ≤100m (open, sunny weather) | ≤100m (open, sunny weather) |
| Output Torque | 1.2N.M*140=160N.M | 0.86N.M*140=120N.M |
| Running Noise＜ | 45dB | 45dB |
| Surface Treatment | Outdoor metal powder electrostatic spraying | Outdoor metal powder electrostatic spraying |
Functions and Features:
1. Gate automatically open when power off, no clutch design, no
need human intervention. When power on,
gate automatically reset, restore to the gate closing state, truly
unattended, fire safety standards. If special
requirement, manual operation is required when power off, operating
arm open and close manually also can
be realized by setting up control board DIP switch, which ensure
that the system can be used at any time.
2. The use of Single Compression Balance Spring device, good
regulation, no noise, indefatigable, not easy to break, safe and
reliable.
3. A variety of input and output modes can be selected, normally
open normally closed are optional.
4. Arm opening angle can be adjusted from 60 to 90 degrees, 10
degrees resolution, suitable for eaves prominent place to install.
5. Closing speed can be adjusted.
6. Barrier gate up &down signal relay switch output.
7. Barrier gate running state: OK signal output indicating that the
gate is working properly.
8. Barrier gate operation abnormal alarm signal output.
9. R&G Traffic light relay switch signal output.
10. External loop detector signal anti-smashing interface, infrared
sensor signal anti-smashing interface.
11. Count mode interface.
12. Arm Open priority anti-smashing function. No matter the current
gate in what state, the operator through the triple
push button, software or remote control to issue an open command,
the gate will give priority to the implementation of the opening
action.
13. Barrier with anti-collision protection function, when the
vehicle hits the gate arm, arm can be swing out to avoid
damage to the vehicle, and barrier gate machine.
14. Delay closed selection function.
15. High-sensitivity arm auto reverse function (intensity can be
adjusted).
16. Parking system interface.
17.RS485 or RS232 network communication control up &down
interface (no need to install communication module)
18. Anti-collision alarm signal interface.
19. Adjustable speed port (from 0.9s to 10 s)
20. High-strength precision cast steel, industry moving parts
beyond the industry quality |
Security Tips:
1 General Security Information
The design, manufacture and testing of the barrier system are use
of the "state-of-the-art" technology and can
only be manufactured after the satisfaction of the strict safety
and reliability of technical standards. Even so,
if the barrier system is not properly operated, it will also cause
danger to people and property. So this manual must be fully read
and all of the safety information must be followed.
If the barrier system is improperly used or used for non-intended
use, the
manufacturer will refuse to be responsible for the resulting
consequences and will cancel the original quality assurance.
2 Suggested Application
High-speed barrier gates can only be used for toll stations for
highways and trunk roads.
The medium barrier gates are designed to control the access roads,
multi-storey car parking lot and other vehicular access routes for
vehicle parking areas.
The controller is specifically designed to control the barrier
gates.
It is not permissible to use these barrier gates for any other
purpose.
Any changes and replacements to the barrier gates and the control
components are prohibited.
3 Safety sign
The following symbols used in this instruction are used to indicate
potential hazards and other safety information.
4 Operating Safety
A safety margin of at least 500 mm must be provided between the end
of barrier gates and the physical obstructions
(such as buildings, walls and fences, etc.) that are closest to it.
When the boom is moving, the personnel and other
objects are forbidden to stay near the barrier gate. If you have
installed the barrier and operating elements and are
connected to a fixed main power supply, you must use a full
polarity with a safety device. It must be operated in
accordance with this installation manual, and be approved by the
company before making any changes. The locking
device of the boom is designed to bear winds of magnitude 10 (=
500N / ㎡.). If it’s expected that there will be a
higher speed wind, must be approved by the company before change
the fixed device of boom. A boom more than
3.5meter will be required to install a swing support or a support
column. All of the circuit connections, wiring work
and replacement of any circuit components must be carried out by
professionally trained electricians. Please firstly
disconnect the connections with main power supply before opening
barrier gates. It is forbidden to make technical
modification or changes to the barrier system.
After cutting off the power, start at least 10 seconds before
starting again.
5 Technology Development
The manufacturer reserves the right to modify the technical
specifications of the product to meet the latest technological
developments without prior notice. The company is glad to provide
the information about current operating manual and
any information about the changes and extensions.
FAQ:
Q: Are you trading company or manufacturer ?
A: We are a professional barrier gate manufacturer.
Q: How long is your delivery time?
A: Generally it is 2-5 days if the goods are in stock. or it is 5-7
days if the goods are not in stock, it is according
to quantity.We can send it for you by DHL/Fedex/TNT/SEA/AIR or your
requirments.
Q: How about payment terms our company provide?
A: T/T or Western Union.
Q: Do you provide free samples ?
A:No,we don't provide free samples. The MOQ of our products is
1pcs.
If you have any question, please contact us freely!
Sales representatives: Keira
Whatsapp: +86 18507481610
Skype: zimin1314
Email: keira@wonsunbarrier.com
