Access Control 110 / 220V Vehicle Barrier Gate Parking Barrier Arm
Gate
What are the disadvantages of Vehicle Barrier Gate barriers?
1. Special driving structure, no gears, non-belt driving,
maintenance free, high stability, longer life.
2. Special balancing structure design makes the barrier arm have
the features of slow-starting, fast-running, and slow-stopping.
3. It is running without arm-shaking.
4. The Vehicle Barrier Gate arm is 90 degrees running which
excludes the failure caused by 360 degrees running.
5. Special low-speed aluminum housing motor integrated gearbox
design, low noise, fast heat dissipation.
6. The Vehicle Barrier Gate driving mechanism has the design of an
intelligent overheating protection system, in frequent use, it can
control the warming of the motor, making the motor not burn easily.
7. The Vehicle Barrier Gate main engine adopts a mechanical limit
switch and photoelectric limit switch dual protection, to avoid the
problems caused by using a traditional magnetic switch which is
easily interfered with by the external environment.
8. Vehicle Barrier Gate arm can be chosen from 1m to 6m.
Vehicle Barrier Gate Model Selection and Differences
| Boom type | Boom Length(L) | Diameter of the spring(mm) | Note |
| Straight boom | 6M≥L≥5M | 5.5/4.5 | |
| 5M≥L≥4.5M | 5.5 | Dispatching 4.5 |
| 4.5M≥L≥3M | 4.5 | Dispatching 4.5 |
| Straight boom adhesive tape | 5M≥L≥4M | 4.5M≥L≥3M | 5.5/4.5 | Dispatching 4.5 |
| 4M≥L≥3M | 3.5M≥L≥3M | 4.5 | Dispatching 4.5 |
| Folding boom | 6M≥L≥5M | 6.5/4.5 | |
| 5M≥L≥4M | 5.5/4.5 | |
| 4M≥L≥3M | 4.5 | |
| Two fence boom | 5M≥L≥4M | 6.5/5.5 | |
| Fence boom | | 4M≥L≥3M | 5.5/4.5 | |
| Three fence boom | 4M≥L≥3M | 6.5/5.5 | |
| | 3M≥L≥2M | 5.5/4.5 | |
Vehicle Barrier Gate Specifications
Model | DZTP-128-B |
Working Temperature | -40℃～+75℃ |
Voltage | 220V±10%, 110V±10%, 50/60HZ |
Rated power | 80W |
Relative humidity | ≤90% |
Remote control distance | ≥30m |
Net weight | 48kgs |
Speed | 1S,1.8S,3S, 6S |
Max boom length | 6 meters |
Motor Rotational speed | 1400rmp |
Protection Degree | IP54 |
Why choose us?
1. One year's free servicing is supplied( not including the arm)
2. Lifetiom charged servicing is offered.
3. Technology servicing is supplied
The following situations are charged for servicing (or changing):
1. Broken by wrong installation.
2 Broken by improper Vehicle Barrier Gate voltage.
3. The surfaces of the system were destroyed by the wrong
installation our use.
4. Broken by natural disaster.
5. Overdue
6. Servicing items out of our promises.
The upgrade and improvement of the product won't be notified if
there is any.
The explaining authority of this product instruction and service
article belongs to the production factory.
Communication with customers
1) Q: Connected power and pressed open/close button but the traffic
barrier gate did not action.
A | Reason | Solution |
1 | Fuse blown | Check the fuse and power in the controller |
2 | The battery of the remote control powered off | Change a new one |
3 | External protection circuit break or at protecting status | Open the barrier door and click the OPEN/CLOSE button on the
control box |
4 | Same frequency interference | Check photocell and loop detector |
2) Q: Connected power and press the open/close button, the traffic
barrier gate will move but even when it is in the right position,
the motor still runs and does not stop.
A | Reason | Solution |
1 | Limit switch | Adjust the horizontal/vertical limit switch to the correct position |
2 | Main controller failure | Change a new one |
3) Q: The motor running but the traffic barrier gate arm is not in
action?
A | Reason | Solution |
1 | Vehicle Barrier Gate arm at 45° position where is hard to move | Unlock the clutch and manually rotate the arm to a horizontal or
vertical position then try again |
2 | The tension of the balancing spring is not suitable | Adjust spring exactly |
3 | Low working voltage | Check the voltage and power |
4) Q: When opening/closing, traffic barrier gate arm cannot reach
the right position (90° vertical & 180° horizontal)?
A. | Reason | Solution |
1 | Length adjustment of connecting rod not correct | Open the vehicle barrier gate door and unlock the clutch to check
when the arm is at 90° vertical position if the master rod covers slave one; when the arm
is at 180° horizontal position if the master rod and slave one are in the
same straight line |
2 | Nuts on the limit switch loose | Tighten the nuts when the arm at 90° vertical and 180° horizontal position |
Contact us for pricelist and catalog:
Sue Zhang
Email:sue@wonsunbarrier.com
Skype: SueZhang729
Whatsapp:+86 158 7925 9831
