Adjustable 0.6s to 6s Automatic Barrier Gate Parking Lot Barrier
Gate
1 pcs Automatic Barrier Gate
1 pcs Automatic Barrier Gate arm boom (from 1m to 6m can
customized)
1 pcs Automatic Barrier Gate control panel(built inside)
2 pcs Automatic Barrier Gate remote controllers
1 pcs Automatic Barrier Gate manual book
Automatic Barrier Gate Model Selection and Differences
| Automatic Barrier Gate Boom type | Boom Length(L) | Diameter of the spring(mm) | Note |
| Automatic Barrier Gate Straight boom | 6M≥L≥5M | 5.5/4.5 | |
| 5M≥L≥4.5M | 5.5 | Dispatching 4.5 |
| 4.5M≥L≥3M | 4.5 | Dispatching 4.5 |
| Straight boom adhesive tape | 5M≥L≥4M | 4.5M≥L≥3M | 5.5/4.5 | Dispatching 4.5 |
| 4M≥L≥3M | 3.5M≥L≥3M | 4.5 | Dispatching 4.5 |
| Automatic Barrier Gate Folding boom | 6M≥L≥5M | 6.5/4.5 | |
| 5M≥L≥4M | 5.5/4.5 | |
| 4M≥L≥3M | 4.5 | |
| Two fence boom | 5M≥L≥4M | 6.5/5.5 | |
| Automatic Barrier Gate Fence boom | | 4M≥L≥3M | 5.5/4.5 | |
| Three fence boom | 4M≥L≥3M | 6.5/5.5 | |
| | 3M≥L≥2M | 5.5/4.5 | |
Automatic Barrier Gate Specifications
Automatic Barrier Gate Model | DZTP-128-B |
Working Temperature | -40℃～+75℃ |
Automatic Barrier Gate Voltage | 220V±10%, 110V±10%, 50/60HZ |
Automatic Barrier Gate Rated power | 80W |
Automatic Barrier Gate Relative humidity | ≤90% |
Remote control distance | ≥30m |
Automatic Barrier Gate Net weight | 48kgs |
Automatic Barrier Gate Speed | 1S,1.8S,3S, 6S |
Max boom length | 6 meters |
Motor Rotational speed | 1400rmp |
Protection Degree | IP54 |
Automatic Barrier Gate Advanced Features:
1) A clutch key can be used to open the clutch when power is off.
2)Fan cooling machine reduces the motor temperature by high
frequency using, never get heat-protecting, unique temperature
calefaction design for low temperature using, prevent freezing in
cold weather.
3) An exactitude aluminum alloy die-casting motor base reduces the
noise and joint abrasion to prolong the barrier gate's working
life.
Why choose us?
1. One year's free servicing is supplied( not including the arm)
2. Lifetiom charged servicing is offered.
3. Technology servicing is supplied
The following situations are charged for servicing (or changing):
1. Broken by wrong installation.
2 Broken by improper voltage.
3. The surfaces of the system were destroyed by the wrong
installation our use.
4. Broken by natural disaster.
5. Overdue
6. Servicing items out of our promises.
The upgrade and improvement of the product won't be notified if
there is any.
The explaining authority of this product instruction and service
article belongs to the production factory.
Communication with customers
1) Q: Connected power and pressed the open/close button but the
traffic barrier gate no action.
A | Reason | Solution |
1 | Fuse blown | Check the fuse and power in the controller |
2 | The battery of the remote control powered off | Change a new one |
3 | External protection circuit break or at protecting status | Open the Automatic Barrier Gate door and click the OPEN/CLOSE
button on the control box |
4 | Same frequency interference | Check photocell and loop detector |
2) Q: Connected power and press the open/close button, the traffic
barrier gate will move but even when it is in the right position,
the motor still runs and does not stop.
A | Reason | Solution |
1 | Limit switch | Adjust the horizontal/vertical limit switch to the correct position |
2 | Main controller failure | Change a new one |
3) Q: The motor running but the traffic barrier gate arm is not in
action?
A | Reason | Solution |
1 | Automatic Barrier Gate arm at 45° position where is hard to move | Unlock the clutch and manually rotate the arm to a horizontal or
vertical position then try again |
2 | The tension of the balancing spring is not suitable | Adjust spring exactly |
3 | Low working voltage | Check the voltage and power |
4) Q: When opening/closing, traffic barrier gate arm cannot reach
the right position (90° vertical & 180° horizontal)?
A. | Reason | Solution |
1 | Length adjustment of connecting rod not correct | Open the barrier door and unlock the clutch to check when the arm
is at 90° vertical position if the master rod covers slave one; when the arm
is at 180° horizontal position if the master rod and slave one are in the
same straight line |
2 | Nuts on the limit switch loose | Tighten the nuts when the arm at 90° vertical and 180° horizontal position |
Contact us for pricelist and catalog:
Sue Zhang
Email:sue@wonsunbarrier.com
Skype: SueZhang729
Whatsapp:+86 158 7925 9831
