2mm Cold Rolled Steel Sheet Parking Barrier Systems Blue And Orange
Specifications
Model | DZ-132 |
Working Temperature | -40℃～+75℃ |
Voltage | 220V±10%, 110V±10%, 50/60HZ |
Rated power | 80W |
Relative humidity | ≤90% |
Remote control distance | ≥30m |
Net weight | 48kgs |
Speed | 1S,1.8S,3S, 6S |
Max boom length | 6 meters |
Motor Rotational speed | 1400rmp |
Protection Degree | IP44 |
What is the davantages of Wonsun barriers?
1)The humanized clutch device:in case of power off, unlock the
clutch device and raise the boom manufally. By the time the power
is supplied, lick the clutch device to make it working normally
again.
2)Special spring device:Both the compression spring and tension
spring can be used in the machine, Using the compression sprin can
avoid accidents caused by the tension spring.
3)Three control buttons:for boom raising, falling and pausing.
4)Boom backtrack function:the boom will rise if hits something when
falling.
5)Infrared photocell design:for avoiding the crash when the boom
falling, so as to prevent the vehicles from being pressed.
6)Both external and internal loop detectors are supported.
7)"open","close" and "stop" controlling interfaces.
8)RS-485 communication serial interface(optional)
9)Traffic light signal connection device: red light for stop,green
light for pass.
10)Remote control and wire control for selection.
Communication with customers
1) Q: Connected power and press open/close button but traffic
barrier gate no action?
A | Reason | Solution |
1 | Fuse blown | Check fuse and power in controller |
2 | Battery of remote control powered off | Change a new one |
3 | External protection circuit break or at protecting status | Open the barrier door and click OPEN/CLOSE button on control box |
4 | Same frequency interference | Check photocell and loop detector |
2) Q:Connected power and press open/close button,traffic barrier
gate will move but even when it is at right position, the motor
still running and not stop?
A | Reason | Solution |
1 | Limit switch | Adjust the horizontal/vertical limit switch to correct position |
2 | Main controller failure | Change a new one |
3) Q: Motor running but traffic barrier gate arm no action?
A | Reason | Solution |
1 | Barrier arm at 45° position where is hard to move | Unlock clutch and manually rotate arm to horizontal or vertical
position then try again |
2 | Tension of balancing spring not suitable | Adjust spring exactly |
3 | Low working voltage | Check the voltage and power |
4) Q: When opening/closing,traffic barrier gate arm cannot reach
right position (90° vertical & 180° horizontal)?
A. | Reason | Solution |
1 | Length adjustment of connecting rod not correct | Open barrier door and unlock clutch to check when arm at 90° vertical position if the master rod covers slave one; when arm at
180° horizontal position if master rod and slave one are in the same
straight line |
2 | Nuts on the limit switch loose | Tighten the nuts when arm at 90° vertical and 180° horizontal
|
| Market | Revenue(Previous Year) | Total Revenue (%) |
| North America | USD 63,608 | 1 |
| South America | USD 508,869 | 8 |
| Eastern Europe | USD 3,180,436 | 50 |
| Southeast Asia | USD 318,043 | 5 |
| Oceania | USD 127,217 | 2 |
| Mid East | USD 190,826 | 3 |
| Western Europe | USD 1,017,739 | 16 |
| Domestic Market | USD 954,130 | 15 |
Why choose us?
1.One year's free servicing is supplied( not including the arm)
2. Lifetiom charged servicing is offered.
3. Technology servicing is supplied
The following situations are charged for servicing (or changing):
1. Broken by wrong installation.
2 Broken by improper voltae.
3. The surfaces of the system destroyed by wrong installation our
use.
4. Broken by natural disaster.
5. Overdue
6. Servicing items out of our promises.
The upgrade and improvement of the product won't be notified if
there is any.
The explaining authority of this product instruction and service
article belong to the production factory.
Contact us for pricelist and catalog:
Sue Zhang
Email:sue@wonsunbarrier.com
Skype:SueZhang729
Whatsapp:+86 158 7925 9831
