| Menu code | Parameter Scale | Parameter name | Default | Unit | Remark |
| H00-00 | 25-95 | Open speed adjustment | 40 | | Corresponding PWM duty cycle 25%-95%, step size is 1 |
| H00-01 | 25-95 | Close speed adjustment | 40 | | Corresponding PWM duty cycle 25%-95%, step size is 1 |
| H00-02 | 5-40 | Open in place decelerate angle | 35 | | The larger the angle value, the less likely it is to shake the arm
when it is in place. |
| H00-03 | 5-40 | Close in place decelerate angle | 35 | | The larger the angle value, the less likely it is to shake the arm
when it is in place. |
| H00-04 | 1-20 | Open accelerate adjustment | 1 | ms | The smaller the number, the faster the speed |
| H00-05 | 1-20 | Close accelerate adjustment | 8 | ms | The smaller the number, the faster the speed |
| H00-06 | 1-30 | Open in place angle | 1 | degree | step size is 1, when big than
11, will automatically check one side |
| H00-07 | 1-30 | Close in place angle | 1 | degree | step size is 1 |
| H00-08 | 7-13 | Auto reverse force adjustment | 10 | A | step size is 1 |
| H00-09 | 0-90 | Delay closing adjustment | 0 | second | step size is 100；0 is not closing automatically,Other value will be
closing automatically; This parameter is for the situation that
there is no loop detector signals and non-automatic operation
occasions |
| H00-10 | 10-50 | Self-check speed adjustment | 30 | | Corresponding PWM duty cycle 10%-50%, step size is 1 |
| H00-11 | 0-2 | Self-check mode | 0 | | 0:no operate automatically；1:operate automatically, eliminate after
power off；2:operate automatically,Power failure
memory.3.intelligent automatically operation. |
| H00-12 | 0-5 | Self-lock force adjustment | 0 | | 0:Invalid , 1or 2 valid |
| H00-13 | 1-20 | Motor deceleration time when paused | 5 | | The larger the setting, the longer the pause time will take |
| H00-14 | 0-1 | Bid-direction setting | 0 | | 0:Closing,1:opening |
| H00-15 | 0-2 | Energy saving closing arm direction | 0 | | 0:invalid 1:close arm valid(energy saving voltage is determined by 49 items ) 2:open arm valid |
| H00-16 | 1-32 | RS485communication address | 1 | | Up to 32 slaves can be connected |
| H00-17 | 0-2 | RS485communication rate | 0 | | 0:9600,1:19200,2:38400；Change the parameter and will be valid after
power on again. |
| H00-18 | 0-2 | Whether to self-check when power on | 1 | | 0:no self-check,1:self-check；2:self-check with remote control; |
| H00-19 | 0-3 | self-check setting | 2 | | 0:Manually invalid,1:Keyboard SET button,2:remote control
valid,3,Keyboard SET button and remote control both valid |
| H00-20 | 0-15 | Monitoring parameter setting index | 7 | | 0 | 0XD000 | Rotate speed | 0~2500 |
| 1 | 0XD001 | Motor feedback angle | 0~90 degree |
| 2 | 0XD002 | Busbar voltage(V) | 0~40.0 |
| 3 | 0XD003 | Current output | |
| 4 | 0XD004 | Hall state | 0~7 |
| 5 | 0XD005 | Commutation number | |
| 6 | 0XD006 | Total number of trips | |
| 7 | 0XD007 | Run time(ms) | 0~9000 |
| 8 | 0XD008 | Cumulative running times | 0`99999999 |
| 9 | 0xD00A | Time of automation operation | 0~99999999 |
| 10 | 0xD00C | Time of anti-Collision | 0~99999999 |
| 11 | 0xD00E | The number of times of the arm is close in place | 0~99999999 |
| 12 | 0xD010 | Power on time(minute) | 0~99999999 |
| 13 | 0xD012 | Power supply power on times | 0~99999999 |
| 14 | 0xD014 | Running status | Binary display |
| 15 | 0xD015 | Fault code | 0~7 |
| 19 | | Number of UP arm | 0-65535 |
| 20 | | Number of DOWN arm | 0-65535 |
| 21 | | Number of STOP | 0-65535 |
| 22 | | Number of Loop detector | 0-65535 |
| 23 | | Number of Photocell | 0-65535 |
| 24 | | Number of Camera | 0-65535 |
| H00-21 | 0-3 | Factory data reset | 0 | | 1:Factory data rest,2:cumulative number of times cleared
3:Accumulate the number of times to clear and restore factory
settings, return to 0 after execution |
| H00-22 | 0-1 | Start acceleration time constant | 0 | | The higher the value, the slower the acceleration |
| H00-23 | 12-30 | Minimal output | 10 | | Minimum output duty cycle of UP/DOWN arm |
| H00-24 | 12-30 | STOP key function setting | | | 0:whenever you press pause, ARM stay in the current state 1:when
close arm, press the STOP key to switch the arm to up command |
| H00-25 | 1-20 | Reserve | | | |
| H00-26 | 0-1 | Camera count timeout(seconds) | | S | 0:count cleared when10 minutes time out, Not 0 is timing close arm |
| H00-27 | 0-1 | | | | |
| H00-28 | 0-3 | LED light output mode | | | 0:Do not flash alternately during operation；1:Allow flashing;
2:Green light when UP arm on 45 Degree |
| H00-33 | | 485 communication status control | | | 485 communication, analog input port data |
| H00-34 | | Peak pattern | 0-1 | | Long press remote control whether to prohibit the use of IO port;
0: No prohibition effect; 1: effective |
arrier Gate 6m Arm with DC24V Brushless Motor For Parking lot SYSTE
